Visual inspection
Cords, plugs and casings checked for cuts, crush damage, cracks, scorch marks and dodgy repairs. A lot of faults show up here before a meter is plugged in.
Electrical safety, Echuca and Moama
Test and Tag Services Near Echuca
Searching for test and tag near you in Echuca? We come to you. Cafes, wineries, houseboat operators, workshops and schools on both sides of the river get their gear tested and tagged on site.
Local testing, on your schedule
Echuca and Moama businesses get busy in the tourist season, and nobody wants to lose a day of trade for testing. We work through your site area by area, so each item is only out of use for the minute it takes to test.
All testing follows AS/NZS 3760. You get a tag on every item, a register of what was tested and a note of anything that failed. We cover Victorian and NSW sites, so one provider can look after your gear on both sides of the Murray.
What We Check on Every Appliance
Anything with a plug gets the same process, from the office kettle to the angle grinder in the back of the ute.
Earth continuity
On earthed (Class I) appliances we confirm the earth runs from the plug pin to the metal body, so a fault trips the circuit instead of livening the case.
Insulation resistance
A test between the live parts and the outside of the appliance, to make sure the insulation will keep current where it belongs.
Polarity on leads
Extension leads and power boards are checked so active, neutral and earth are wired to the right pins from end to end.
Tag and register
Each item that passes is tagged with the test date and the next due date, then logged in a register you can hand to an auditor.
Failed items
Anything that fails is tagged out of service and taken out of use on the spot. We tell you what failed so you can repair or replace it.
How Often Gear Is Tested
AS/NZS 3760 sets the interval by how hard the equipment is used. We look at your site and tell you the right interval, rather than testing everything on the shortest one.
Every three months
Building and construction sites, and hire equipment before it goes out.
Every six to twelve months
Factories, workshops, commercial cleaning and other tough environments where gear is moved and knocked about.
Up to five years
Equipment in low-risk areas like offices, where it is not moved around or likely to be damaged.
Between Tests
Simple habits that keep electrical gear safe in the months between visits.
- Look over cords and plugs before use. If something is cut, cracked or hot, stop using it.
- Do not daisy-chain power boards or run leads under rugs and through doorways.
- Keep new gear aside for testing, or note it in your register when it arrives.
- Pull out anything with an out-of-date tag and keep it out of use until it is tested.
Add to the same visit
One booking, one report.
- Fire extinguisher servicing
- Fire safety equipment
- RCD testing
- Exit and emergency lighting
- First aid kits
- Evacuation diagrams
How a Service Works
Book a serviceBook a Time
Call or send a request. We book a visit that suits your hours and work around your team.
We Test On Site
Every extinguisher, light, appliance and kit checked and tagged. Problems are pointed out while we are there.
Report and Reminder
You get a written report, and we contact you before the next service falls due.
Echuca and Both Sides of the Murray
From our base in Kyabram we test and tag for Echuca, Moama and Rochester, and further up the river to Deniliquin.
- Echuca
- Moama
- Rochester
- Kyabram
- Deniliquin
Also in: Kyabram, Shepparton, Bendigo
What Our Clients Say
Test and tag FAQs
Common questions from Echuca and Moama businesses. Anything else, just ask.
Book a serviceDo you test and tag in Moama and NSW?
Yes. We test and tag for sites in Moama and Deniliquin as well as Echuca, so businesses with sites in both states can use one provider.
How quickly can you get to Echuca?
It depends on our schedule that week, but Echuca is a regular run for us. Call and we will give you the next available date.
Is test and tag a legal requirement?
Workplace health and safety laws require employers to manage electrical risks, and AS/NZS 3760 is the standard most workplaces and insurers use to show that is being done. On construction sites, regular testing is required outright. We can tell you what applies to your site.
What happens if an item fails?
It gets an out-of-service tag and is taken out of use straight away. We explain why it failed, and it is listed in your report so you have a record of what was found and what was done about it.
Do you test new equipment?
New equipment does not need a test before its first use under AS/NZS 3760, but it does need to go on your register and be tested at the next interval. We can tag new gear as new to service so it is tracked from day one.
Can you do other safety checks on the same visit?
Yes. Most sites book test and tag alongside RCD testing, fire extinguishers, exit and emergency lighting and first aid kits, so everything is done in one visit and one report.
Safety Checked.
Box Ticked.
Tell us what you have on site and we will come back to you with a time and a clear quote. Prefer to talk? Call Paul.
- 0407 877 482
- admin@ambaguard.com.au
- Mon to Fri, 8 AM to 4 PM
Book a service
Fields marked * are required.
Thanks, request sent.
We will be in touch within business hours (Mon to Fri, 8 AM to 4 PM) with a time and a quote. Need us sooner? Call 0407 877 482.